ASTM A213 Alloy Pipes

ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes

ASTM A213M-09 standard is issued under the fixed designation A 213/A 213M; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

ASTM A213 T5 Seamless alloy pipe

ASTM A213 T5 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T91 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213
  • Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes
  • A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes.
  • Piping wall thicknesses range from 1/2 inch to 5 inches.
  • A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T5 Low Alloy Steel

Grade/ Material

Element

Composition( Max-A, Min-I)

A335 P5/ UNS K41545

C

A:0.15

Mn

A:0.30-0.60

Si

A:0.50

P

0.025

S

0.025

Cr

4.00-6.00

Mo

0.45-0.65

Mechanical Properties( Mpa)

Grade/ Material

Tensile Test

Ksi/MPa

A335 P5/ UNS K41545

Tensile Strength

I:60/415

Yield Strength

I:30/205

Elongation

I:30%

Impact Test( if any)

ASTM A213 T5b Seamless alloy tube

ASTM A213 T5b seamless alloy steel pipe - ASTM A213 Alloy Pipes

ASTM A213 T5b Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.

ASTM A213 T5b measurment out diameter - ASTM A213 Alloy Pipes

Measurment out diameter

ASTM A213 T5b Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

ASTM A213 T5b measurment wall thickness - ASTM A213 Alloy Pipes

Measurment Wall thickness

ASTM A213 T5b measurment length - ASTM A213 Alloy Pipes

Measurment Lenth

ASTM A213 T5b packing in wooden boxes - ASTM A213 Alloy Pipes

Packing in wooden boxes

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T5b tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

Mechanical properties for ASTM A213 T5b Low Alloy Steel
  • Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes;
  • A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes.
  • Piping wall thicknesses range from 1/2 inch to 5 inches.
  • A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

ASTM A213/ASME SA213 T5b Tubes Chemistry Composition

C, %
Mn, %
P, %
S, %
Si, %
Cr, %
Mo, %
0.15 max
0.30-0.60
0.025 max
0.025 max
1.00-2.00
4.00-6.00
0.45-0.65

ASTM A213/ASME SA213 T5b Tubes Mechanical Properties

Tensile Strength , MPa
Yield Strength, MPa
Elongation, %
Hardness, HB
415 min
205 min
30 min
179 max

ASTM A213/ASME SA213 T5b Tubes Outside Diameter & Tolerance

Hot rolled
Outside Diameter, mm
Tolerance, mm
OD≤101.6
+0.4/-0.8
101.6<OD≤190.5
+0.4/-1.2
190.5<OD≤228.6
+0.4/-1.6
Cold Drawn
Outside Diameter, mm
Tolerance, mm
OD<25.4
±0.10
25.4≤OD≤38.1
±0.15
38.1<OD<50.8
±0.20
50.8≤OD<63.5
±0.25
63.5≤OD<76.2
±0.30
76.2≤OD≤101.6
±0.38
101.6<OD≤190.5
+0.38/-0.64
190.5<OD≤228.6
+0.38/-1.14

ASTM A213/ASME SA213 T5b Tubes Wall thickness & Tolerance

Hot rolled
Outside Diameter, mm
Tolerance, %

OD≤101.6, WT≤2.4

+40/-0
OD≤101.6, 2.4<WT≤3.8
+35/-0
OD≤101.6, 3.8<WT≤4.6
+33/-0
OD≤101.6, WT>4.6
+28/-0
OD>101.6, 2.4<WT≤3.8
+35/-0
OD>101.6, 3.8<WT≤4.6
+33/-0
OD>101.6, WT>4.6
+28/-0
Cold Drawn
Outside Diameter, mm
Tolerance, %
OD≤38.1
+20/-0
OD>38.1
+22/-0

Length: 5800mm; 6000mm; 6096mm; 7315mm; 11800mm; 12000mm; and so on. 
Max length: 16000mm, also U bending can be offered.
Keyword: High Pressure Steel Pipe, Boiler Steel Pipe, Heat Exchanger Steel Tube, ASME SA213, SA213T5b, ASTM A213

End User

  • T11 for power generation, petroleum, and other high temperature services
  • T22 for power generation, petroleum, and other high temperature services
  • T5 for petroleum
  • T9 for petroleum
  • T91 for power generation
  • T92 for power generation
  • T1 for boiler replacement and repair

ASTM A213 T5b Standard Scope

1.1 This specification covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes, designated Grades T91, TP304, etc. These steels are listed in Tables 1 and 2.
1.2 Grades containing the letter, H, in their designation, have requirements different from those of similar grades not containing the letter, H. These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements.
1.3 The tubing sizes and thicknesses usually furnished to this specification are 1/8 in. [3.2 mm] in inside diameter to 5 in. [127 mm] in outside diameter and 0.015 to 0.500 in. [0.4 to 12.7 mm], inclusive, in minimum wall thickness or, if specified in the order, average wall thickness. Tubing having other diameters may be furnished, provided such tubes comply with all other requirements of this specification.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
TABLE 1 Chemical Composition Limits, %A, for Low Alloy Steel A Maximum, unless range or minimum is indicated. Where ellipses (…) appear in this table, there is no requirement, and analysis for the element need not be determined or reported.

B It is permissible to order T2 and T12 with a sulfur content of 0.045 max. See 16.3.

C Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.

ASTM A213 T9 Seamless alloy pipe

Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T91 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213
  • Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes;
  • A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes.
  • Piping wall thicknesses range from 1/2 inch to 5 inches.
  • A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T9 Low Alloy Steel
UNS Designation K90941
Carbon 015
Manganese 0.30–0.60
Phosphorus 0.025
Sulfur 0.025
Silicon 0.25-1.00
Nickel
Chromium 8.00-10.00
Molybdenum 0.90-1.10
Vanadium
Boron
Niobium
Nitrogen
Aluminum
Tungsten
Other Elements

ASTM A213 T11 Seamless alloy pipe

ASTM A213 T11 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

ASTM A213 T11 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.

Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T91 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213
  • Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes;
  • A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes.
  • Piping wall thicknesses range from 1/2 inch to 5 inches.
  • A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T11 Low Alloy Steel
UNS Designation K11597
Carbon 0.05-0.15
Manganese 0.30–0.60
Phosphorus 0.025
Sulfur 0.025
Silicon 0.50-1.00
Nickel
Chromium 1.00-1.50
Molybdenum 0.44-0.65
Vanadium
Boron
Niobium
Nitrogen
Aluminum
Tungsten
Other Elements
Mechanical properties for ASTM A213 T11 Low Alloy Steel
Tensile strength(min) 415Mpa
Yield strength(min) 220Mpa
Elongation 30%
Delivery condition annealed
ASTM A213 T12 Seamless alloy pipes

ASTM A213 T12 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

ASTM A213 T12 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.

ASTM A213 T12 Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T21 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213

Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes; A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes. Piping wall thicknesses range from 1/2 inch to 5 inches. A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T12 Low Alloy Steel
UNS Designation K11562
Carbon 0.05-0.15
Manganese 0.30–0.61
Phosphorus 0.025
Sulfur 0.025
Silicon 0.50
Nickel
Chromium 0.80-1.25
Molybdenum 0.44-0.65
Vanadium
Boron
Niobium
Nitrogen
Aluminum
Tungsten
Other Elements
ASTM A213 T22 alloy pipe
ASTM A213 T22 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes. ASTM A213 T22 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.

Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T22 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213
  • Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes;
  • A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes.
  • Piping wall thicknesses range from 1/2 inch to 5 inches.
  • A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Chemical Composition(%) for ASTM A213 T22 Low Alloy Steel
UNS Designation K21590
Carbon 0.05-0.15
Manganese 0.30–0.60
Phosphorus 0.025
Sulfur 0.025
Silicon 0.50
Nickel
Chromium 1.90-2.60
Molybdenum 0.87-1.13
Vanadium
Boron
Niobium
Nitrogen
Aluminum
Tungsten
Other Elements

ASTM A213 T91 Seamless alloy tube

ASTM A213 T91 Seamless alloy tube - ASTM A213 Alloy Pipes

ASTM A213 T91 is the part of ASTM A213 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, Heat-Exchanger Tubes.

ASTM A213 T91 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes. We are one of the leading Manufacturers, Supplier and Exporters of high quality ASTM A213 T91 Alloy Steel Seamless Tube. These tubes are widely used in various application industry such as Oil & Gas, Power, Fertilizers, Heat-Exchangers, Paper & Pulp, pharmaceuticals, Chemicals, Water Treatment, Dairy etc.

We are Offered at competitive prices in the market.

ASTM A213 T91 Grades containing the letter H in their designation have requirements different from those of similar grades not containing the letter H.

These different requirements provide higher creep-rupture strength than normally achievable in similar grades without these different requirements. ASTM A213 T91 tubes shall be made by the seamless process and shall be either hot finished or cold finished, as specified. Grade TP347HFG shall be cold finished. Heat treatment shall be done separately and in addition to heating for hot forming. The ferritic alloy and ferritic stainless steels shall be reheated. On the other hand, austenitic stainless steel tubes shall be furnished in the heat-treated condition. Alternatively, immediately after hot forming, while the temperature of the tubes is not less than the minimum solution temperature, tubes may be individually quenched in water or rapidly cooled by other means. Tension test, hardness test, flattening test, and flaring test shall be done to each tube. Also, each tube shall be subjected to the nondestructive electric test or hydrostatic test.

ASTM A209 Through A213

Other standard specifications include the categories of A209 seamless carbon-molybdenum alloy-steel boiler and superheater tubes; A210 seamless medium-carbon steel boiler and superheater tubes and A213 seamless ferritic and austenitic steel boiler, superheater and heat-exchanger tubes. Piping wall thicknesses range from 1/2 inch to 5 inches. A213 grades also have the letter H or M assigned, which changes the composition and specifications for that series.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

ASTM A213/ASME SA213 T91 Tubes Chemistry Composition

C, %
Mn, %
P, %
S, %
Si, %
Cr, %
Mo, %
V, %
N, %
Ni, %
Al, %
Nb, %
0.08-0.12
0.3-0.6
0.02 max
0.01 max
0.2-0.5
8.0-9.5
0.85-1.05
0.18-0.25
0.03-0.07
0.4 max
0.04 max
0.06-0.10

ASTM A213/ASME SA213 T91 Tubes Mechanical Properties

Tensile Strength , MPa
Yield Strength, MPa
Elongation, %
Hardness, HB
585 min
415 min
20 min
250 max

ASTM A213/ASME SA213 T91 Tubes Outside Diameter & Tolerance

Hot rolled
Outside Diameter, mm
Tolerance, mm
OD≤101.6
+0.4/-0.8
101.6<OD≤190.5
+0.4/-1.2
190.5<OD≤228.6
+0.4/-1.6
Cold Drawn
Outside Diameter, mm
Tolerance, mm
OD<25.4
±0.10
25.4≤OD≤38.1
±0.15
38.1<OD<50.8
±0.20
50.8≤OD<63.5
±0.25
63.5≤OD<76.2
±0.30
76.2≤OD≤101.6
±0.38
101.6<OD≤190.5
+0.38/-0.64
190.5<OD≤228.6
+0.38/-1.14

ASTM A213/ASME SA213 T91 Tubes Wall thickness & Tolerance

Hot rolled
Outside Diameter, mm
Tolerance, %

OD≤101.6, WT≤2.4

+40/-0
OD≤101.6, 2.4<WT≤3.8
+35/-0
OD≤101.6, 3.8<WT≤4.6
+33/-0
OD≤101.6, WT>4.6
+28/-0
OD>101.6, 2.4<WT≤3.8
+35/-0
OD>101.6, 3.8<WT≤4.6
+33/-0
OD>101.6, WT>4.6
+28/-0
Cold Drawn
Outside Diameter, mm
Tolerance, %
OD≤38.1
+20/-0
OD>38.1
+22/-0

Length: 5800mm; 6000mm; 6096mm; 7315mm; 11800mm; 12000mm; and so on. 
Max length: 16000mm, also U bending can be offered.
Keyword: High Pressure Steel Pipe, Boiler Steel Pipe, Heat Exchanger Steel Tube, ASME SA213, SA213T91, ASTM A213

ASTM A213 T92 Alloy Steel Seamless Tube

astm a213 t92 alloy steel seamless tube - ASTM A213 Alloy Pipes

We are one of the leading Manufacturers, Supplier and Exporters of high quality ASTM A213 T92 Alloy Steel Seamless Tube. We manufacture these using optimum quality material as per their specified details.

These tubes are widely used in various application industry such as Oil & Gas, Power, Fertilizers, Heat-Exchangers, Paper & Pulp, pharmaceuticals, Chemicals, Water Treatment, Dairy etc.

We are Offered at competitive prices in the market. ASTM A213 T92 Standard covers seamless ferritic and austenitic steel boiler, superheater, and heat-exchanger tubes.

Chemical Compositions :
C, % Mn, % P, % S, % Si, % Cr, % Mo, %
0.07-0.13 0.3-0.6 0.02 max 0.01 max 0.5 max 8.5-9.5 0.3-0.6
V, % N, % Ni, % Al, % Nb, % W, % B, %
0.15-0.25 0.03-0.07 0.4 max 0.04 max 0.04-0.09 1.5-2.0 0.001-0.006
Mechanical Properties :
Tensile Strength , MPa Yield Strength, MPa Elongation, % Hardness, HB
585 min 415 min 20 min 250 max
Outside Diameter & Tolerance :
Hot rolled Outside Diameter, mm Tolerance, mm
OD≤101.6 +0.4/-0.8
101.6<OD≤190.5 +0.4/-1.2
190.5<OD≤228.6 +0.4/-1.6
Cold Drawn Outside Diameter, mm Tolerance, mm
OD<25.4 ±0.10
25.4≤OD≤38.1 ±0.15
38.1<OD<50.8 ±0.20
50.8≤OD<63.5 ±0.25
63.5≤OD<76.2 ±0.30
76.2≤OD≤101.6 ±0.38
101.6<OD≤190.5 +0.38/-0.64
190.5<OD≤228.6 +0.38/-1.14
Wall thickness & Tolerance :
Hot rolled Outside Diameter, mm Tolerance, %
OD≤101.6, WT≤2.4 +40/-0
OD≤101.6, 2.4<WT≤3.8 +35/-0
OD≤101.6, 3.8<WT≤4.6 +33/-0
OD≤101.6, WT>4.6 +28/-0
OD>101.6, 2.4<WT≤3.8 +35/-0
OD>101.6, 3.8<WT≤4.6 +33/-0
OD>101.6, WT>4.6 +28/-0
Cold Drawn Outside Diameter, mm Tolerance, %
OD≤38.1 +20/-0
OD>38.1 +22/-0

Length: 5800mm; 6000mm; 6096mm; 7315mm; 11800mm; 12000mm; and so on.

Max length: 16000mm, also U bending can be offered.

Source: China Alloy Pipe Manufacturer – Yaang Pipe Industry (www.steeljrv.com)

(Yaang Pipe Industry is a leading manufacturer and supplier of nickel alloy and stainless steel products, including Super Duplex Stainless Steel Flanges, Stainless Steel Flanges, Stainless Steel Pipe Fittings, Stainless Steel Pipe. Yaang products are widely used in Shipbuilding, Nuclear power, Marine engineering, Petroleum, Chemical, Mining, Sewage treatment, Natural gas and Pressure vessels and other industries.)

If you want to have more information about the article or you want to share your opinion with us, contact us at sales@steeljrv.com
Please notice that you might be interested in the other technical articles we’ve published:

  • How to get high quality alloy steel pipes
  • Knowledges of seamless steel pipes
  • How to get high quality stainless steel pipes
  • What is a welded steel pipe
  • Difference between galvanized steel pipe and seamless steel pipe
  • The difference between steel tubes and steel pipes
  • How to get high quality steel pipes
  • How to get high quality carbon steel pipes
  • How To Distinguish Inferior Steel Pipe
  • What is the difference between a steel pipe and a steel tube
  • Manufacturing process of cold rolled steel pipe

  • Cold Working Processes of Steel Pipes
  • The cutting processing technology of stainless steel pipe
  • The production process of welded stainless steel pipe
 • How to get high quality astm a335 chrome moly pipe
 • What is a welded steel pipe

 • How to get high quality ASTM A333 alloy pipes

 • ASTM A519

References:

  • https://www.yaang.com
  • https://www.astm.org/Standards/A213.htm

Related News

  • * 暂无相关文章
العربيةБългарски简体中文繁體中文DanskNederlandsEnglishFrançaisDeutschBahasa IndonesiaItaliano日本語한국어LatinPortuguêsРусскийEspañolதமிழ்ไทยTürkçe