DIN 2576 A182 F304L Plate Flange DN80 PN16

Chemical Composition and Mechanical Property for 304/304L
Steel Grade	Chemical Composition									Mechanical Performance
	C(Max)	Si(Max)	Mn(Max)	P(Max)	S(Max)	Ni	Cr	N	Mo	Tensile Strength (Min)	Yield Strength (Min)
										Mpa	Mpa
304	0.08	0.75	2.00	0.045	0.03	8.0–10.5	18.0–20.0	0.1	/	515	205
304L	0.03	0.75	2.00	0.045	0.03	8.0–12.0	18.0–20.0	0.1	/	485	170

PLATE FLANGE DIN 2576 PN10

20191222063727 68920 - DIN 2576 A182 F304L Plate Flange DN80 PN16

Germany standard flange DIN 2576 for soldering or welding Nominal Pressure10
Flansche, glatt zum löten oder schweißen DIN 2576 Nenndruck 10
Brides plates a souder DIN 2576 pression nominale 10
Pipe			Flange					Screws			Weight (7,85 Kg/dm3)
Rated Diameter	d1		d5	D	b	c	k	Holes	Thread	d2	Kg
	ISO Series 1	DIN Series 2
15	–	20	21	95	14	5	65	4	M 12	14	0,675
	21,3	–	22								0,669
20	–	25	26	105	16	5	75	4	M 12	14	0,749
	26,9	–	27,6								0,936
25	–	30	31	115	16	5	85	4	M 12	14	1,14
	33,7	–	34,4								1,11
32	–	38	39	140	16	5	100	4	M 16	18	1,66
	42,4	–	43,1								1,62
40	–	44,5	45,5	150	16	5	110	4	M 16	18	1,89
	48,3	–	49								1,86
50	–	57	58,1	165	18	6	125	4	M 16	18	2,51
	60,3	–	61,1								2,47
65	76,1	–	77,1	185	18	6	145	4	M 16	18	3
80	88,9	–	90,3	200	20	7	160	8	M 16	18	3,79
100	–	108	109,6	220	20	7	180	8	M 16	18	4,2
	114,3	–	115,9								4,03
125	–	133	134,8	250	22	7	210	8	M 16	18	5,71
	139,7	–	141,6								5,46
150	–	159	161,1	285	22	7	240	8	M 20	22	6,72
	168,3	–	170,5								6,57
200	219,1	–	221,8	340	24	7	295	8	M 20	22	9,31
250	–	267	270,2	395	26	7	350	12	M 20	22	12,5
	273	–	276,2								11,9
300	323,9	–	327,6	445	26	7	400	12	M 20	22	13,8
350	355,6	–	359,7	505	28	7	460	16	M 20	22	20,6
	–	368	372,2								19
400	406,4	–	411	565	32	7	515	16	M 24	26	27,9
	–	419	423,7								25,9
450	457	–	462,5	615	38	7	565	20	M 24	26	35,6
500	508	–	513,6	670	38	7	620	20	M 24	26	41,1
NOTE: 1. Facing according to DIN 2526 Flat face: Form A, Face without any requirements Form B, Face Rz=160, machined (not smoother than 40µm) Raised Face: Form C, Face Rz=160, machined (not smoother than 40µm) Form D, Face Rz=40, machined Form E, Face Rz=16, machined 2. Tongue and groove according to DIN 2512 Form F, Tongue Form N, Groove 3. Male and Female according to DIN 2513, DIN 2514 Form V13, V14, Male Form R13, R16, Female 4. Chemfering for diaphragm-weld packings, PN64-PN400, according to DIN 2695 5. Facing for lens-shaped joints, PN64-PN400, according to DIN 2696

DIN EN 1092-1 PN-40

20191222063727 68920 - DIN 2576 A182 F304L Plate Flange DN80 PN16

EN 1092-1 TYPE 01 PN40 PLATE FLANGE
Rated Diameter	Pipe	Flange				Screws			Weight (7,85 Kg/dm3)
Rated Diameter	Pipe	d1	k	D	b	d2	Thread	Bolt holes	KG
15	21,3	22,0	65	95	14	14	M12	4	0,668
20	26,9	27,5	75	105	16	14	M12	4	0,933
25	33,7	34,5	85	115	16	14	M12	4	1,106
32	42,4	43,5	100	140	18	18	M16	4	1,816
40	48,3	49,5	110	150	18	18	M16	4	2,075
50	60,3	61,5	125	165	20	18	M16	4	2,723
65	76,1	77,5	145	185	22	18	M16	8	3,465
80	88,9	90,5	160	200	24	18	M16	8	4,310
100	114,3	116,0	190	235	26	22	M20	8	6,056
125	139,7	141,5	220	270	28	26	M24	8	8,170
150	168,3	170,5	250	300	30	26	M24	8	10,238
200	219,1	221,5	320	375	36	30	M27	12	17,871
250	273,0	276,5	385	450	42	33	M30	12	29,166
300	323,9	327,5	450	515	52	33	M30	16	44,921
350	355,6	359,5	510	580	58	36	M33	16	66,460
400	406,4	411,0	585	660	65	39	M36	16	96,822

* For flanges type 21 the outside hub diameter approximately corresponds to the outside pipe diameter.
Note : The p/t rating from EN 1092-1 apply only for flange type 05, 11, 12, 13 and 21 having nominal sizes up to and including DN 600. The p/t rating of all other flanges shall be agreed between the manufacturer and the purchaser.

Plate flange PN 16 – acc. to EN 1092-1 type 01

Comparison DIN and EN
For nominal sizes larger than DN 150, EN standardizes pressure levels PN 10 and PN 16.
From DN 50 to DN 150, the EN refers to the standard series of PN 16 pressure level.
For dimensions up to DN 40, the EN refers to the standard series of PN 40 pressure level.
New in EN 1092-1 are the pressure levels PN 16 and PN 40 for plate flanges.
The European standard EN 1092-1/01 has replaced the national standard DIN 2576 in 2007.

Standards

DIN (old)

DIN 2576 PN 10

EN (new)

EN 1092-1 type 01 PN 16

In contrast to the DIN standard, EN-1092-1 only specifies the pipe connection dimensions of the ISO series.
It is therefore sufficient to stamp the nominal diameter (DN) for marking purposes.

Dimension range

DIN 2576

DN 10 to 500

EN 1092-1

DN 50 to 1000

(Druckstufe PN 10) (Dimensions for DN < 50 see PN 40)

Designation of the gasket shape

Shape B

Shape A

Seal surface

Machining

Rotaded

Ra (µm)

min. 3,25 / max. 12,5

Rz (µm)

min. 12,5/ max. 50

<br>

DIN 2576 Flange Material

Carbon Steel DIN 2576 Flange	ASTM/ASME A/SA105 A/SA105N & A/SA216-WCB, DIN 1.0402, DIN 1.0460, DIN 1.0619, Die Steel, ASTM A105 / ASME SA105, A105N, ASTM A350 LF2 / ASME SA350, High Yield CS ASTM A694 / A694 (F52 F56 F60 F65 F70 F80)
Stainless Steel DIN 2576 Flange	ASTM/ASME A/SA182 F304, F304L, F316, F316L, ASTM/ASME A/SA351 CF8, CF3, CF8M, CF3M, DIN 1.4301, DIN 1.4306, DIN 1.4401, DIN 1.4404, DIN 1.4308, DIN 1.4408, DIN 1.4306, DIN 1.4409
Alloy Steel DIN 2576 Flange	ASTM A182 / ASME SA182 F5, F9, F11, F12, F22, F91
Titanium DIN 2576 Flange	ASTM B381 / ASME SB381, Titanium Gr. 1, Titanium Gr. 2, Titanium Gr. 4, Titanium Gr. 5, Titanium Gr. 7 ASTM R50250/GR.1 \| R50400/GR.2 \| R50550/GR.3 \| R50700/GR.4 \| GR.6 \| R52400/GR.7 \| R53400/GR.12 \| R56320/GR.9 \|R56400/GR.5
Copper DIN 2576 Flange	T1, T2, C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910,C10920, TP1, TP2, C10930, C11000, C11300, C11400, C11500, C11600, C12000,C12200, C12300, TU1, TU2, C12500, C14200, C14420, C14500, C14510, C14520, C14530, C17200, C19200, C21000, C23000, C26000, C27000, C27400, C28000, C33000, C33200, C37000, C44300, C44400, C44500, C60800, C63020, C68700, C70400, C70600, C70620, C71000, C71500, C71520, C71640, etc
Copper Nickel DIN 2576 Flange	ASTM / ASME SB 61 / 62 / 151 / 152, Copper Nickel 90/10 (C70600 ), Cupro Nickel 70/30 (C71500), UNS C71640
Brass DIN 2576 Flange	3602 / 2604 / H59 / H62 / etc.
Inconel DIN 2576 Flange	ASTM B564 / ASME SB564, Inconel 600, 601, 625, 718, 783, 690, x750 DIN 2576 Flange
Hastelloy DIN 2576 Flange	ASTM B564 / ASME SB564, Hastelloy C276 (UNS N10276), C22 (UNS N06022), C4, C2000, B2, B3, X Flanges
Monel DIN 2576 Flange	ASTM B564 / ASME SB564, Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500)
Alloy 20 DIN 2576 Flange	ASTM B462 / ASME SB462, Carpenter® 20 Alloy, Alloy 20Cb-3
Aluminium DIN 2576 Flange	5052 /6061/ 6063 / 2017 / 7075 / etc.
Nickel DIN 2576 Flange	ASTM B564 / ASME SB564, Nickel 200, Nickel 201, Nickel 205, Nickel 205LC
Duplex DIN 2576 Flange	S31803 / S32205 A182 Gr F51 / F52 / F53 / F54 / F55 / F57 / F59 / F60 / F61
Super Duplex DIN 2576 Flange	S32750 / S32760 A182 Gr F51 / F52 / F53 / F54 / F55 / F57 / F59 / F60 / F61
Incoloy DIN 2576 Flange	ASTM B564 / ASME SB564, Incoloy 800, 800H, 800HT (UNS N08800), 825 (UNS N08825), 925 Flanges
254 Smo DIN 2576 Flange	ASTM A182 / ASME SA182, SMO 254/6Mo, UNS S31254, DIN 1.4547
Nimonic DIN 2576 Flange	Nimonic 75, Nimonic 80A, Nimonic 90
Other DIN 2576 Flange material	Tin bronze, Alumunum bronze, Lead bronze