European pipe standards (EN pipe standards)

20211002025828 46382 - European pipe standards (EN pipe standards)

European pipe standards (EN pipe standards)

Number Chinese name English name
CR 12952-17-2002 锅炉水管道和辅助设备 第17部分:独立于制造商的检查机构参与指南 Water boilers and auxiliary installations – Part 17: Guideline for the involvement of an inspection body independent of the manufacturer
CR 13932-2000 旋转动力泵 管道系统的进口和出口管件建议书 Rotodynamic pumps – Recommendations for fitting of inlet and outlet on piping
EN 10208-1-1997 易燃流体管道用钢管 交货技术条件 第1部分:符合A类要求的管材 Steel pipes for pipelines for combustible fluids – Technical delivery conditions – Part 1: Pipes of requirement class A
EN 10208-2-1996+AC-1996 易燃流体管道用钢管 交货技术条件 第2部分:符合B类要求的管材 Steel pipes for pipelines for combustible fluids – Technical delivery conditions – Part 2: Pipes of requirement class B
EN 1053-1995 塑料管道系统 无压力情况下使用的热塑管道系统 水密封性的试验方法 Plastics piping systems – Thermoplastics piping systems for non-pressure applications – Test method for watertightness
EN 1054-1995 塑料管道系统 粪便和污水排放用热塑管道系统 连接件气密性试验方法 Plastics piping systems – Thermoplastics piping systems for soil and waste discharge – Test method for airtightness of joints
EN 1055-1996 塑料管道系统 建筑物内粪便和污水排放用热塑管道系统 抗周期性升温的试验方法 Plastics piping systems – Thermoplastics piping systems for soil and waste discharge inside buildings – Test method for resistance to elevated temperature cycling
EN 1093-6-1998 机械安全 空气中有害物质排放的评估 第6部分:通过未经管道流出的质量来评价分离离效率 Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 6: Separation efficiency by mass, unducted outlet
EN 1093-7-1998 机械安全 空气中有害物质排放的评估 第7部分:通过经管道流出的质量来评价分离离效率 Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 7: Separation efficiency by mass, ducted outlet
EN 1115-1-1997 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第1部分:概述 Plastics piping systems for underground drainage and sewerage under pressure – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 1: General
EN 1115-3-1996 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第3部分:配件 Plastics piping systems for underground drainage and sewerage under pressure – Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 3: Fittings
EN 1115-5-1996 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第5部分:连接 Plastics piping systems for underground drainage and sewerage under pressure – Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 5: Fitness for purpose of the joints
EN 1119-1996 塑料管道系统 玻璃增强热固塑料管和配件用接头 挠性和还原接合接头密封性和耐损伤性试验方法 Plastics piping systems – Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings – Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints
EN 1120-1996 塑料管道系统 玻璃增强热固塑料管和配件 偏斜条件下内部一个截面耐化学品侵袭的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes and fittings – Determination of the resistance to chemical attack from the inside of a section in a deflected condition
EN 1123-1-1999 废水系统用带套管的纵向焊接热浸镀锌钢管管道及配件 第1部分:要求、测试和质量控制 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control
EN 1123-1/prA1-2002 废水系统用带套管的纵向焊接热浸镀锌钢管管道及配件 第1部分:要求、测试和质量控制 修改A1 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control; Amendment A1
EN 1123-2-1999 废水系统用带套管和插口的纵向焊接热浸镀锌钢管管道及配件 第2部分:尺寸 Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems – Part 2: Dimensions
EN 1124-1-1999 废水系统用带套管和插口的纵向焊接不锈钢管管道及配件 第1部分:要求、测试、质量控制 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control
EN 1124-1/prA1-2002 废水系统用带套管和插口的纵向焊接不锈钢管管道及配件 第1部分:要求、测试、质量控制 修改A1 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 1: Requirements, testing, quality control; Amendment A1
EN 1124-2-1999 废水系统用带套管和插口的纵向焊接不锈钢管管道和配件 第2部分:系统S 尺寸 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 2: System S – Dimensions
EN 1124-3-1999 废水系统用带套管和插口的纵向焊接不锈钢管管道及配件 第3部分:系统X 尺寸 Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems – Part 3: System X – Dimensions
EN 12056-2-2000 建筑物内的重力排水系统 第2部分:卫生间管道工程的布局和计算 Gravity drainage systems inside buildings – Part 2: Sanitary pipework, layout and calculation
EN 12061-1999 塑料管道系统 热塑性管件 耐冲击试验方法 Plastics piping systems – Thermoplastics fittings – Test method for impact resistance
EN 12095-1997 塑料管道系统 雨水管道系统用托架 托架强度的试验方法 Plastics piping systems – Brackets for rainwater piping systems – Test method for bracket strength
EN 12099-1997 塑料管道系统 聚乙烯管材和组件 挥发含量的测定 Plastics piping systems – Polyethylene piping materials and components – Determination of volatile content
EN 12100-1997 塑料管道系统 聚乙稀(PE)阀门 支架间抗弯曲性的试验方法 Plastics piping systems – Polyethylene (PE) valves – Test method for resistance to bending between supports
EN 12106-1997 塑料管道系统 聚乙稀(PE)管 压出后抗内压性的试验方法 Plastics piping systems – Polyethylene (PE) pipes – Test method for the resistance to internal pressure after application of squeeze-off
EN 12107-1997 塑料管道系统 压注热塑管件、阀门和辅助设备 管道组件压注用热塑 材料的长期液压强度的测定 Plastics piping systems – Injection-moulded thermoplastics fittings, valves and ancillary equipment – Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components
EN 12117-1997 塑料管道系统 热塑管件、阀门和配件 气流速率/压降之间关系的测定 Plastics piping systems – Fittings, valves and ancillaries – Determination of gaseous flow rate/pressure drop relationships
EN 12118-1997 塑料管道系统 用库仑计测定热塑性塑料中水分 Plastics piping systems – Determination of moisture content in thermoplastics by coulometry
EN 12119-1997 塑料管道系统 聚乙烯(PE)阀门 抗热循环测试方法 Plastics piping systems – Polyethylene (PE) valves – Test method for resistance to thermal cycling
EN 12200-1-2000 地面上外部使用的塑料雨水管道系统 未增塑聚乙烯(聚氯乙烯)(PVC-U) 第1部分:管道、配件和系统用规范 Plastics rainwater piping systems for above ground external use – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes, fittings and the system
EN 12201-1-2003 供水系统用塑料管道系统 聚乙烯(PE) 第1部分:总则 Plastics piping systems for water supply – Polyethylene (PE) – Part 1: General
EN 12201-2-2003 供水系统用塑料管道系统 聚乙烯(PE) 第2部分:管道 Plastics piping systems for water supply – Polyethylene (PE) – Part 2: Pipes
EN 12201-3-2003 供水系统用塑料管道系统 聚乙烯(PE) 第3部分:配件 Plastics piping systems for water supply – Polyethylene (PE) – Part 3: Fittings
EN 12201-4-2001 供水系统用塑料管道系统 聚乙烯(PE) 第4部分:阀门 Plastics piping systems for water supply – Polyethylene (PE) – Part 4: Valves
EN 12201-5-2003 供水系统用塑料管道系统 聚乙烯(PE) 第5部分:系统目的的适配性 Plastics piping systems for water supply – Polyethylene (PE) – Part 5: Fitness for purpose of the system
EN 12220-1998 建筑物通风 管道系统 一般通风用圆法兰盘的测定 Ventilation for buildings – Ductwork – Dimensions of circular flanges for general ventilation
EN 12236-2002 建筑物通风 管道悬架和支架 强度需求 Ventilation for buildings – Ductwork hangers and supports – Requirements for strength
EN 12237-2003 建筑物通风 管道系统 圆片金属管的强度和泄漏 Ventilation for buildings – Ductwork – Strength and leakage of circular sheet metal ducts
EN 1225-1996 塑料管道系统 玻璃增强热固性塑料管 潮湿条件下蠕变因子的测定和长期特定环刚度的计算 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness
EN 12256-1998 塑料管道系统 .热塑性塑料配件 装配式配件机械强度或挠度的试验方法 Plastics piping systems – Thermoplastics fittings – Test method for mechanical strength or flexibility of fabricated fittings
EN 1226-1996 塑料管道系统 玻璃增强热固性塑料管 验证初期环状物挠曲阻力的试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Test method to prove the resistance to initial ring deflection
EN 1227-1997 塑料管道系统 玻璃增强热固性塑料管 潮湿条件下长期最终相关环状物挠曲的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the long-term ultimate relative ring deflection under wet conditions
EN 1228-1996 塑料管道系统 玻璃增强热固性塑料管 初始特定环刚度的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of initial specific ring stiffness
EN 1229-1996 塑料管道系统 玻璃增强热固性塑料管 验证短期内部压力下墙的密封性试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes and fittings – Test methods to prove the leaktightness of the wall under short-term internal pressure
EN 12293-1999 塑料管道系统 热水和冷水用热塑性塑料管道和接头 安装组件耐热循环性的试验方法 Plastics piping systems – Thermoplastics pipes and fittings for hot and cold water – Test method for the resistance of mounted assemblies to temperature cycling
EN 12294-1999 塑料管道系统 热水和冷水系统 真空下气密性的试验方法 Plastics piping systems – Systems for hot and cold water – Test method for leaktightness under vacuum
EN 12295-1999 塑料管道系统 热水和冷水用热塑性塑料管道和接头 接合处耐压力循环试验方法 Plastics piping systems – Thermoplastics pipes and associated fittings for hot and cold water – Test method for resistance of joints to pressure cycling
EN 12308-1998 液化天然装置和设备 液化天然气管道中所用的法兰接头垫圈设计适配性试验 Installations and equipment for LNG – Suitability testing of gaskets designed for flanged joints used on LNG piping
EN 12474-2001 水下管道的阴极保护 Cathodic protection of submarine pipelines
EN 12514-2-2000 燃油炉供油系统用的装置 第2部分:安全要求和试验 零部件、阀门、管道、滤油器、油气分离器、油量指示表 Installations for oil supply systems for oil burners – Part 2: Safety requirements and tests – Parts, valves, pipes, filters, oil de-aerators, meters
EN 12585-1998 玻璃设备、管道和配件 DN15至1000管道和配件 兼容性和互换性 Glass plant, pipeline and fittings – Pipeline and fittings DN 15 to 1000 – Compatibility and interchangeability
EN 12735-1-2001 铜和铜合金 空调和制冷用无缝圆铜管 第1部分:管道系统用管子 Copper and copper alloys – Seamless, round copper tubes for air conditioning and refrigeration – Part 1: Tubes for piping systems
EN 1277-1996 塑料管道系统 地下无压用热塑管道系统 弹性密封环型接头密封性试验方法 Plastics piping systems – Thermoplastics piping systems for buried non-pressure applications – Test methods for leaktightness of elastomeric sealing ring type joints
EN 12842-2000 PVC-U或PE管道系统用可球墨铸铁配件 要求和试验方法 Ductile iron fittings for PVC-U or PE piping systems – Requirements and test methods
EN 1295-1-1997 不同荷载条件下地下管道结构设计 第1部分:一般要求 Structural design of buried pipelines under various conditions of loading – Part 1: General requirements
EN 12954-2001 掩埋或浸没金属结构的阴极保护 一般原理和管道应用 Cathodic protection of buried or immersed metallic structures – General principles and application for pipelines
EN 13052-1-2001 材料对人类生活用水的影响 有机物 管道系统中水的颜色和浊度的测定 第一部分:试验方法 Influence of materials on water intended for human consumption – Organic materials; Determination of colour and turbidity of water in piping systems – Part 1: Test method
EN 13090-2000 建筑物中气体管道螺纹接头再密封方法 Means for resealing threaded joints of gas pipework in buildings
EN 13136-2001 制冷系统和加热泵 压力释放设备及相关管道 计算方法 Refrigerating systems and heat pumps – Pressure relief devices and their associated piping – Methods for calculation
EN 13180-2001 建筑物通风 管道系统 柔性管的尺寸和机械要求 Ventilation for buildings – Ductwork – Dimensions and mechanical requirements for flexible ducts
EN 13220-1998 与医用气体管道系统的终端设备相连的流量计 Flow-metering devices for connection to terminal units of medical gas pipeline systems
EN 13244-1-2002 地上和地下给排水和污水压力系统用塑料管道 聚已烯(PE) 第1部分:总则 Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage – Polyethylene (PE) – Part 1: General
EN 13244-2-2002 地上和地下给排水和污水压力系统用塑料管道 聚已烯(PE) 第2部分:管道 Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage – Polyethylene (PE) – Part 2: Pipes
EN 13244-3-2002 地上和地下给排水和污水压力系统用塑料管道 聚已烯(PE) 第3部分:配件 Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage – Polyethylene (PE) – Part 3: Fittings
EN 13244-4-2002 地上和地下给排水和污水压力系统用塑料管道 聚已烯(PE) 第4部分:阀门 Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage – Polyethylene (PE) – Part 4: Valves
EN 13244-5-2002 地上和地下给排水和污水压力系统用塑料管道 聚已烯(PE) 第5部分:系统适用度 Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage – Polyethylene (PE) – Part 5: Fitness for purpose of the system
EN 1329-1-1999 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVC-U) 第1部分:管材、管件和系统规 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes, fittings and the system
EN 13312-1-2001 生物技术 管道和仪器性能标准 第1部分:一般的性能标准 Biotechnology – Performance criteria for piping and instrumentation – Part 1: General performance criteria
EN 13312-2-2001 生物技术 管道和仪器性能标准 第2部分 联接器 Biotechnology – Performance criteria for piping and instrumentation – Part 2: Couplings
EN 13312-3-2001 生物技术 管道和仪器性能标准 第3部分:取样和接种装置 Biotechnology – Performance criteria for piping and instrumentation – Part 3: Sampling and inoculation devices
EN 13312-4-2001 生物技术 管道和仪器性能标准 第4部分:管子和导管 Biotechnology – Performance criteria for piping and instrumentation – Part 4: Tubes and pipes
EN 13312-5-2001 生物技术 管道和仪器性能标准 第5部分:阀 Biotechnology – Performance criteria for piping and instrumentation – Part 5: Valves
EN 13312-6-2001 生物技术 管道和仪器性能标准 第6部分:设备探头 Biotechnology – Performance criteria for piping and instrumentation – Part 6: Equipment probes
EN 1333-1996 管道工程元件 定义和PN的选择 Pipework components – Definition and selection of PN
EN 13403-2003 建筑物通风 非金属管道 由绝热道管板制成的管道系统 Ventilation for buildings – Non-metallic ducts – Ductwork made from insulation ductboards
EN 13467-2001 建筑设备和工业装置用保温制品 预成型管道保温层的尺寸、垂直度和直线度的测定 Thermal insulating products for building equipment and industrial installations – Determination of dimensions, squareness and linearity of preformed pipe insulation
EN 13469-2001 建筑设备和工业装置用保温制品 预成型管道保温层水蒸气传导性的测定 Thermal insulating products for building equipment and industrial installations – Determination of water vapour transmission properties of preformed pipe insulation
EN 13470-2001 建筑设备和工业装置用保温制品 预成型管道保温层表观密度的测定 Thermal insulating products for building equipment and industrial installations – Determination of the apparent density of preformed pipe insulation
EN 13472-2001 建筑设备和工业装置用保温制品 通过部分沉浸法测定预成型管道保温层的短期吸水性 Thermal insulating products for building equipment and industrial installations – Determination of short term water absorption by partial immersion of preformed pipe insulation
EN 13480-1-2002 工业用金属管道 第1部分:总则 Metallic industrial piping – Part 1: General
EN 13480-2-2002 工业用金属管道 第2部分:材料 Metallic industrial piping – Part 2: Materials
EN 13480-3-2002 工业用金属管道 第3部分:设计和计算 Metallic industrial piping – Part 3: Design and calculation
EN 13480-4-2002 工业用金属管道 第4部分:制造和安装 Metallic industrial piping – Part 4: Fabrication and installation
EN 13480-5-2002 工业用金属管道 第5部分:检查和测试 Metallic industrial piping – Part 5: Inspection and testing
EN 13544-2-2002 呼吸治疗设备 第2部分:管道和连接器 Respiratory therapy equipment – Part 2: Tubing and connectors
EN 13566-1-2002 用于修复非压力排水和污水网的塑料管道系统 第1部分:总则 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks – Part 1: General
EN 13566-3-2002 用于修复非压力排水和污水网的塑料管道系统 第3部分:带密装配管的衬套 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks – Part 3: Lining with close-fit pipes
EN 13566-4-2002 用于修复非压力排水和污水网的塑料管道系统 第4部分:带现场固化管的衬套 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks – Part 4: Lining with cured-in-place pipes
EN 13598-1-2003 非压力底下排水和污水塑料管道系统 非增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE) 第1部分:包括 Plastics piping systems for non-pressure underground drainage and sewerage – Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) – Part 1: Specifications for ancillary fittings including shallow inspection chambers
EN 1366-1-1999 服务设施的耐火试验 第1部分:管道 Fire resistance tests for service installations – Part 1: Ducts
EN 1366-5-2003 服务设施的耐火试验 第5部分:作业管道和烟囱 Fire resistance tests for service installations – Part 5: Service ducts and shafts
EN 13689-2002 用于修复的塑料管道系统的分类和设计指南 Guidance on the classification and design of plastics piping systems used for renovation
EN 1393-1996+AC-1997 塑料管道系统 玻璃增强热固性塑料(GRP)管 初始径向拉伸特性的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of initial longitudinal tensile properties
EN 1394-1996+AC-1997 塑料管道系统 玻璃增强热固性塑料(GRP)管 外观初始圆周抗拉强度的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the apparent initial circumferential tensile strength
EN 13942-2003 石油和天然气工业 管道运输系统 管道阀门 Petroleum and natural gas industries – Pipeline transportation systems – Pipeline valves (ISO 14313:1999, modified)
EN 1401-1-1998 非压力地下雨水管和污水管用塑料管道系统未增塑聚氯乙烯(PVC-U) 管道 第1部分:配件和系统规范 Plastics piping systems for non-pressure underground drainage and sewerage – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes, fittings and the system
EN 1411-1996 塑料管道和导管系统 热塑管 用阶梯法测定抗外冲击能力 Plastics piping and ducting systems – Thermoplastics pipes – Determination of resistance to external blows by the staircase method
EN 14163-2001 石油和天然气工业 管道运输系统 管道的焊接 Petroleum and natural gas industries – Pipeline transportation systems – Welding of pipelines (ISO 13847:2000, modified)
EN 1420-1-1999 有机材料对民用水的影响 管道系统中水气味的测定 第1部分:试验方法 Influence of organic materials on water intended for human consumption – Determination of odour and flavour assessment of water in piping systems – Part 1: Test method
EN 1437-2002 塑料管道系统 地下排水和污水用管道系统 耐温度循环和外部负荷综合作用的试验方法 Plastics piping systems – Piping systems for underground drainage and sewerage – Test method for resistance to combined temperature cycling and external loading
EN 1444-2000 纤维水泥管道 现场工作实践和铺设指南 Fibre-cement pipelines – Guide for laying and on-site work practices
EN 1446-1996 塑料管道及导管系统 热塑管 环挠形测定 Plastics piping and ducting systems – Thermoplastics pipes – Determination of ring flexibility
EN 1447-1996 塑料管道系统 玻璃增强热固性塑料管 (GRP) 长期耐内压能力的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of long-term resistance to internal pressure
EN 1448-1996 塑料管道系统 玻璃增强热固塑料(GRP)组件 带弹性密封件的刚性锁紧插承接合的设计查验试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) components – Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals
EN 1449-1996 塑料管道系统 玻璃纤维增强热固性塑料(GRP)组件 查检水泥套管插承接合设计的试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) components – Test methods to prove the design of cemented socket-and-spigot joints
EN 1450-1996+A1-1998 塑料管道系统 玻璃增强热固塑料(GRP)组件 螺栓法兰连接的设计查验试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) components – Test methods to prove the design of bolted flange joints
EN 1451-1-1998 建筑物结构内污物和废水排出(低和高温)用塑料管道系统 聚丙烯(PP ) 第1部分:管材、管件和系统规范 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polypropylene (PP) – Part 1: Specifications for pipes, fittings and the system
EN 1452-1-1999 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第1部分:总则 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: General
EN 1452-2-1999 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第2部分:管材 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 2: Pipes
EN 1452-3-1999 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分:管件 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 3: Fittings
EN 1452-4-1999 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第4部分:阀门和附属设备 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 4: Valves and ancillary equipment
EN 1452-5-1999 供水塑料管道系统 硬塑聚氯乙烯(PVC-U) 第5部分:系统的适合性 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 5: Fitness for purpose of the system
EN 1453-1-2000 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第1部分:管材和系统规 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for pipes and the system
EN 1455-1-1999 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 丙烯腈 丁二烯 苯乙烯共聚物 第1部分:管材、管 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Acrylonitrile-butadiene-styrene (ABS) – Part 1: Requirements for pipes, fittings and the system
EN 1456-1-2001 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) .第1部分:管道组件和系统规范 Plastics piping systems for buried and above-ground drainage and sewerage under pressure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 1: Specifications for piping components and the system
EN 1505-1997 建筑物通风 矩形截面的金属片通风管道和管件 尺寸 Ventilation for buildings – Sheet metal air ducts and fittings with rectangular cross section – Dimensions
EN 1506-1997 建筑物通风 环形截面的金属片通风管道和管件 尺寸 Ventilation for buildings – Sheet metal air ducts and fittings with circular cross-section – Dimensions
EN 1519-1-1999 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 聚乙烯(PE) 第1部分:管材、管件和系统规范 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) – Part 1: Specifications for pipes, fittings and the system
EN 1555-1-2002 供给气体燃料用塑料管道系统 聚已烯(PE) 第1部分:总则 Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 1: General
EN 1555-2-2002 供给气体燃料用塑料管道系统 聚已烯(PE) 第2部分:管材 Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 2: Pipes
EN 1555-3-2002 供给气体燃料用塑料管道系统 聚已烯(PE) 第3部分:管件 Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 3: Fittings
EN 1555-4-2002 供给气体燃料用塑料管道系统 聚已烯(PE) 第4部分:阀门 Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 4: Valves
EN 1555-5-2002 供给气体燃料用塑料管道系统 聚已烯(PE) 第5部分:针对系统用途的适合性 Plastics piping systems for the supply of gaseous fuels – Polyethylene (PE) – Part 5: Fitness for purpose of the system
EN 1565-1-1998 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第1部分:管材、管件和 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Styrene copolymer blends (SAN+PVC) – Part 1: Specifications for pipes, fittings and the system
EN 1566-1-1998 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第1部分:管材、管件和系统 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Chlorinated poly(vinyl chloride) (PVC-C) – Part 1: Specifications for pipes, fittings and the system
EN 1594-2000 供气系统 最大运行压力超过16bar的管道 功能要求 Gas supply systems – Pipelines for maximum operating pressure over 16 bar – Functional requirements
EN 1636-3-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第3部分:管件 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 3: Fittings
EN 1636-5-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第5部分:针对接头 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 5: Fitness for purpose of the joints
EN 1636-6-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第6部分:安装实践 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 6: Practices for installation
EN 1638-1997 塑料管道系统 玻璃增强热固塑料管道(GRP) 循环内压效果的试验方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Test method for the effects of cyclic internal pressure
EN 1680-1997 塑料管道系统 聚乙烯(PE)管道系统用阀门 传动装置的弯曲时和弯曲后密封性的试验方法 Plastics piping systems – Valves for polyethylene (PE) piping systems – Test method for leaktightness under and after bending applied to the operating mechanism
EN 1704-1997 塑料管道系统 热塑阀门 弯曲情况下温度周期变化后阀门完整性的试验方法 Plastics piping systems – Thermoplastics valves – Test method for the integrity of a valve after temperature cycling under bending
EN 1705-1996 塑料管道系统 热塑阀门 外部鼓风后阀门完整性试验方法 Plastics piping systems – Thermoplastics valves – Test method for the integrity of a valve after an external blow
EN 1716-1997 塑料管道系统 聚乙烯(PE)分接三通管 分接三通管组件上耐冲击能力的检测方法 Plastics piping systems – Polyethylene (PE) tapping tees – Test method for impact resistance of an assembled tapping tee
EN 1775-1998+A1 -2000+A2-2000 供气 建筑物中的气体管道工程 最大运转压力≤5巴功能推荐 Gas supply – Gas pipework for buildings – Maximum operating pressure 5 bar – Functional recommendations
EN 1852-1-1997+A1-2001 无压地下排水和污水用塑料管道系统 聚丙烯(PP)、 第一部分:管材、管件及系统规范 Plastics piping systems for non-pressure underground drainage and sewerage – Polypropylene (PP) – Part 1: Specifications for pipes, fittings and the system
EN 1861-1998 制冷系统和热泵 系统流程图和管道及仪表图表 平面图和符号 Refrigerating systems and heat pumps – System flow diagrams and piping and instrument diagrams – Layout and symbols
EN 1862-1997 塑料管道系统 玻璃增强热固塑料管(GRP) 暴露在化学环境后相关挠曲蠕变因素的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the relative flexural creep factor following exposure to a chemical environment
EN 187105-2002 单模光纤电缆(管道/直埋安装) Single mode optical cable (duct/direct buried installation)
EN 1905-1998 塑料管道系统 硬聚氯乙烯管、管件和材料 基于氯的总含量评估聚氯乙烯含量的方法 Plastics piping systems – Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material – Method for assessment of the PVC content based on total chlorine content
EN 1979-1999 塑料管道和管道系统 热塑螺旋型结构壁的管材 接缝拉伸强度的测定 Plastics piping and ducting systems – Thermoplastics spirally-formed structured-wall pipes – Determination of the tensile strength of a seam
EN 1989-2000 热塑性管道系统 埋地无压污水用接头 通过估计密封压力对热塑弹性塑料(TPE)密封接头的长时间密封性能的试 Thermoplastics piping systems – Joints for buried non-pressure sewerage applications – Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the sealing pressure
EN 24006-1993 封闭管道中液体流量的测量.名词和符号 Measurement of fluid flow in closed conduits; vocabulary and symbols (ISO 4006:1991)
EN 24185-1993 封闭管道中液体流量的测量 重量法 Measurement of liquid flow in closed conduits; Weighing method (ISO 4185:1980)
EN 253-2003 分区供暖管 直接掩埋热水网用预隔热连接的管道系统 成套钢铁管道设备的管组件、聚氨酯热绝缘和聚乙烯外覆 District heating pipes – Preinsulated bonded pipe systems for directly buried hot water networks – Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene
EN 288-9-1999 金属材料焊接程序规范和鉴定 第9部分:传输管道陆地和海上场所对接焊中管道焊接用焊接程序试验 Specification and approval of welding procedures for metallic materials – Part 9: Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines
EN 29104-1993 封闭管道中流体流量测量 液体电磁流量计性能评定方法 Measurement of fluid flow in closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids (ISO 9104:1991)
EN 4028-2001 航空航天系列 钛合金管连接 8°30′ 在管道上有推力丝螺母的三通 Aerospace series – Pipe coupling 8?0 in titanium alloy – Tees with thrust wire nut on run
EN 4030-2001 航空航天系列 钛合金管连接 8°30′ 在管道上的T形舱壁 Aerospace series – Pipe coupling 8?0 in titanium alloy – Tees bulkhead on run
EN 4190-2001 空航天系列 钛合金管连接8°30′ 管道上有推力丝螺母的异径三通 Aerospace series – Pipe coupling 8 Degree 30′in titanium alloy – Tees, reduced with thrust wire nut on run
EN 448-2003 热水分配管道 地下热水网用预隔热包覆层的管道系统 聚氨酯热绝缘和聚乙烯外覆层的钢铁管的配件 District heating pipes – Preinsulated bonded pipe systems for directly buried hot water networks – Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
EN 45510-7-1-1999 发电站设备、设备和系统的采购指南 第7-1部分:管道系统和阀门 高压管道系统 Guide for procurement of power station plant, equipment, and systems – Part 7-1: Pipework and valves – High pressure piping systems
EN 45510-7-2-1999 发电站设备、设备和系统的采购指南 第7-2部分:管道系统和阀门 锅炉和高压管道阀 Guide for procurement of power station plant, equipment, and systems – Part 7-2: Pipework and valves – Boiler and high pressure piping valves
EN 474-9-1998 土方机械 安全 第9部分:管道敷设机的要求 Earth-moving machinery – Safety – Part 9: Requirements for pipelayers
EN 476-1997 用于排水管道组件、重力系统的排水管的一般要求 General requirements for components used in discharge pipes, drains and sewers for gravity systems
EN 488-2003 热水分配管道 地下热水网用预先绝热包覆的管道系统 成套钢铁管道设备的管阀门组件、聚氨酯热绝缘和聚乙 District heating pipes – Preinsulated bonded pipe systems for directly buried hot water networks – Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
EN 489-2003 热水分配管道 地下热水网用预隔热包覆的管道系统 成套钢铁管道设备的接头组件、聚氨酯热绝缘和聚乙烯外 District heating pipes – Preinsulated bonded pipe systems for directly buried hot water networks – Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
EN 50085-1-1997+A1-1998 电气装置用电缆槽和电缆管道系统 第1部分:一般要求 Cable trunking systems and cable ducting systems for electrical installations – Part 1: General requirements
EN 50085-1/prA2-2002 电气装置用电缆槽和电缆管道系统 第1部分:一般要求 修改PrA2 Cable trunking systems and cable ducting systems for electrical installations – Part 1: General requirements; Amendment A2
EN 50085-2-3-1999 电气装置用电缆槽和电缆管道系统 第2-3部分:箱式设备用有槽电缆槽系统的特殊要求 Cable trunking systems and cable ducting systems for electrical installations – Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
EN 50249-2002 地下管道和电缆的定位器 性能与安全 Electromagnetic locators for buried pipes and cables – Performance and safety
EN 512-1994+A1-2001 纤维水泥制品 压力管道和接头 Fibre-cement products – Pressure pipes and joints
EN 545-2002 给水管道用球墨铸铁管、配件、附件及其接头 要求和试验方法 Ductile iron pipes, fittings, accessories and their joints for water pipelines – Requirements and test methods
EN 578-1993 塑料管道系统 塑料管和配件 不透明度的测定 Plastics piping systems – Plastics pipes and fittings – Determination of the opacity
EN 579-1993 塑料管道系统 交联聚乙烯(PE-X)管 溶剂萃取法测定交联密度 Plastics piping systems – rosslinked polyethylene (PE-X) pipes -Determination of degree of crosslinking by solvent extraction
EN 580-2003 塑料管道系统 未增塑聚氯乙烯(PVC-U)管 特定温度下耐二氯甲烷试验方法 Plastics piping systems – Unplasticized poly(vinyl chloride) (PVC-U) pipes – Test method for the resistance to dichloromethane at a specified temperature (DCMT)
EN 588-1-1996 污水管和排水管用纤维水泥管 第1部分:重力系统用管道、管连接件和管配件 Fibre-cement pipes for sewers and drains – Part 1: Pipes, joints and fittings for gravity systems
EN 60794-3-10-2002 光纤电缆 第3-10部分:室外电缆 管道和直接填埋的通讯光缆的族规范 Optical fibre cables – Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables (IEC 60794-3-10:2002, modified) / Note: Endorsement notice
EN 637-1994 塑料管道系统 玻璃增强塑料部件 用重量分析法测定成分含量 Plastics piping systems – Glass-reinforced plastics components – Determination of the amounts of constituents using the gravimetric method
EN 681-1-1996+A1-1998 +A2-2002+AC-2002 弹性密封件 供水和排水管道用管联接密封件的材料要求 第1部分:琉化橡胶 Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 1: Vulcanized rubber
EN 681-2-2000+A1-2002 弹性密封件 供水和排水管道用管联接密封件的材料要求 第2部分:热塑性合成橡胶 Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 2: Thermoplastic elastomers
EN 681-3-2000+A1-2002 弹性密封件 供水和排水管道用管联接密封件的材料要求 第3部分:硫化橡胶的泡沫材料 Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 3: Cellular materials of vulcanized rubber
EN 681-4-2000+A1-2002 弹性密封件 供水和排水管道用管联接密封件的材料要求 第4部分:浇铸聚氨酯密封元件 Elastomeric seals – Materials requirements for pipe joint seals used in water and drainage applications – Part 4: Cast polyurethane sealing elements
EN 682-2002 弹性密封件 用于运送气体和碳氢化合物液体的管道和配件的密封件的材料要求 Elastomeric seals – Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids
EN 705-1994 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管和配件 回归分析及其使用方法 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes and fittings – Methods for regression analysis and their use
EN 712-1993 热塑管道系统 压力管和配件间承受机械接合件的端部负载 在恒定径向力下抗拔出性能的试验方法 Thermoplastics piping systems – End-load bearing mechanical joints between pressure pipes and fittings – Test method for resistance to pull-out under constant longitudinal force
EN 713-1993 塑料管道系统 配件和聚烯烃压力管间的机械接合件 弯曲时组件内部压力密封性的试验方法 Plastic piping systems – Mechanical joints between fittings and polyolefin pressure pipes – Test method for leaktightness under internal pressure of assemblies subjected to bending
EN 714-1994 热塑管道系统 压力管和模塑配件间的无端部负载的弹性密封环型接合件 在无轴向推力时内部流体静力学压力下 Thermoplastics piping systems – Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings – Test method for leaktightness under internal hydrostatic pressure without end thrust
EN 715-1994 热塑管道系统 小直径压力管和配件间端部负荷的接合件 在包含轴向推力的内部水压下密封性的试验方法 Thermoplastics piping systems – End-load bearing joints between small diameter pressure pipes and fittings-Test method for leaktightness under internal water pressure, including end thrust
EN 727-1994 塑料管道和导管系统 热塑性管和配件 维卡(Vicat)软化温度(VST)的测定 Plastics piping and ducting systems – Thermoplastics pipes and fittings – Determination of Vicat softening temperature (VST)
EN 728-1997 塑料管道和导管系统 聚烯烃管和配件 氧化感应时间的测定 Plastics piping and ducting systems – Polyolefin pipes and fittings – Determination of oxidation induction time
EN 737-1-1998 医疗气体管道系统 第1部分:压缩医疗气体和真空用终端设备 Medical gas pipeline systems – Part 1: Terminal units for compressed medical gases and vacuum
EN 737-2-1998+A1 -1999+AC-2000 医疗气体管道系统 第2部分:麻醉气体净化处理系统 基本要求 Medical gas pipeline systems – Part 2: Anaesthetic gas scavenging disposal systems – Basic requirements
EN 737-3-1998+A1 -1999+AC-2000 医疗气体管道系统 第3部分:压缩医疗气体和真空用管道 Medical gas pipeline systems – Part 3: Pipelines for compressed medical gases and vacuum
EN 737-4-1998 医疗气体管道系统 第4部分:麻醉气体净化系统的终端设备 Medical gas pipeline systems – Part 4: Terminal units for anaesthetic gas scavenging systems
EN 743-1994 塑料管道和导管系统 热塑管 纵向复原的测定 Plastic piping and ducting systems -Thermoplastics pipes -Determination of the longitudinal reversion
EN 744-1995 塑料管道和导管系统 热塑管 连续法耐外部吹风的试验方法 Plastics piping and ducting systems – Thermoplastics pipes – Test method for resistance to external blows by the round-the-clock method
EN 761-1994 塑料管道系统 玻璃增强热固性塑料管 干燥条件蠕变系数的测定 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the creep factor under dry conditions
EN 763-1994 塑料管道和导管系统 喷射铸模热塑型配件 外观检查加热效果的试验方法 Plastics piping and ducting systems – Injection-moulded thermoplastics fittings – Test method for visually assessing effects of heating
EN 802-1994 塑料管道和导管系统 压力管道系统的喷射铸造热塑性部件 挤压最大变形试验方法 Plastics piping and ducting systems – Injection-moulded thermoplastics fittings for pressure piping systems – Test method for maximum deformation by crushing
EN 803-1994 塑料管道系统 压力管道的弹性密封环状连接的喷射铸造热塑性部件 无轴向推力的瞬时内压阻力试验方法 Plastics piping systems – Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping – Test method for resistance to a short-term internal pressure without end thrust
EN 804-1994 塑料管道系统 压力管道溶焊接头的喷射铸造插接部件 瞬时内部液压阻力的试验方法 Plastics piping systems – Injection-moulded socket fittings for solvent-cemented joints for pressure piping – Test method for resistance to a short-term internal hydrostatic pressure
EN 911-1995 塑料管道系统 热塑塑料压力管道用的弹性密封环型接头和机械接头 外部液压条件下防漏密封试验方法 Plastics piping systems – Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping – Test method for leaktightness under external hydrostatic pressure
EN 921-1994+AC-1995 塑料管道系统 热塑管 恒定温度下耐内压的测定 Plastics piping systems – Thermoplastics pipes – Determination of resistance to internal pressure at constant temperature / Note: To be replaced by prEN ISO 1167-1 (2003-04), prEN ISO 1167-2 (2003-04).
EN 922-1994 塑料管和管道系统 未增塑聚氯乙烯管道和配件 粘度值测定和K值计算的样品准备 Plastics piping and ducting systems – Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) – Specimen preparation for determination of the viscosity number and calculation of the K-value
EN 969-1995+A1-1998 煤气管道用球墨铸铁管、配件、附件及其接头 要求和试验方法 Ductile iron pipes, fittings, accessories and their joints for gas pipelines – Requirements and test methods
EN ISO 10380-2003 管道系统 波纹金属软管和软管组件 Pipework – Corrugated metal hoses and hose assemblies (ISO 10380:2003)
EN ISO 10472-3-1997 工业洗衣机安全要求 第3部分:管道式洗涤(联合)机及相关机械 Safety requirements for industrial laundry machinery – Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997)
EN ISO 10807-1996 管道工程 在爆燃性空气中电缆保护用皱纹软金属管组件 Pipework – Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmosphere (ISO 10807:1994)
EN ISO 11691-1995 声学 无气流管道消声器插入损失的测量 实验室测量法 Acoustics – Measurement of insertion loss of ducted silencers without flow – Laboratory survey method (ISO 11691:1995)
EN ISO 13703-2000 石油和天然气工业 海上开采平台上管道系统的设计和安装 Petroleum and natural gas industries – Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
EN ISO 13783-1997 塑料管道系统 硬聚氯乙烯(PVC-U)端部承受负荷的双承口连接件 密封和承受弯曲及内压的试验方法 Plastics piping systems – Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints – Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997)
EN ISO 13844-2000 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 负压下密封试验方法 Plastics piping systems – Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes – Test method for leaktightness under negative pressure (ISO 13844:2000)
EN ISO 13845-2000 塑料管道系统 用于硬(聚氯乙烯)(PVC-U) 管道的弹性密封环式承口连接件 内压下角度偏转密封试验方法 Plastics piping systems – Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes – Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000)
EN ISO 13846-2000 塑料管道系统 热塑性加压塑料管道用端部负载轴承和非端部负载轴承的安装和连接 在内水压下长期密封的试验 Plastics piping systems – End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping – Test method for long-term leaktightness under internal water pressure (ISO 13846:2000)
EN ISO 14723-2001 石油和天然气工业 管道输送系统 海底管道阀 Petroleum and natural gas industries – Pipeline transportation systems – Subsea pipeline valves (ISO 14723:2001)
EN ISO 15493-2003 工业用塑料管道系统 丙烯腈丁二烯苯乙烯(ABS),未增塑聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C)米制部件 Plastics piping systems for industrial applications – Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) – Specificatio
EN ISO 15494-2003 工业用塑料管道系统 聚丁烯(PB),聚乙烯(PE)和聚丙烯(PP) 米制部件和系统规范 Plastics piping systems for industrial applications – Polybutene (PB), polyethylene (PE) and polypropylene (PP) – Specifications for components and the system; Metric series (ISO 15494:2003)
EN ISO 15908-2002 热塑塑料管道用胶粘剂 胶粘剂热稳定性的测试方法 Adhesives for thermoplastic piping systems – Test method for the determination of thermal stability of adhesives (ISO 15908:2002)
EN ISO 16871-2003 塑料管道和导管系统 塑料管道和配件 直接(自然)风化的方法 Plastics piping and ducting systems – Plastics pipes and fittings – Method for exposure to direct (natural) weathering (ISO 16871:2003)
EN ISO 5136-2003 声学 风机或其他空气移动装置辐射入管道中的声功率的测定 管道法 Acoustics – Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method (ISO 5136:2003)
EN ISO 5167-1-2003 用压差装置测量流体流量 第1部分:圆截面管道中插入的节流孔板、喷嘴和文杜利管 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full – Part 1: General principles and requirements (ISO 5167-1:2003)
EN ISO 5167-2-2003 圆截面管道中用压差装置测量流体流量 第2部分:锐孔法 Measurement of fluid flow by means of pressure differential devices in circular cross-section conduits running full – Part 2: Orifice plates (ISO 5167-2:2003)
EN ISO 5167-3-2003 圆截面管道中用压差装置测量流体流量 第3部分:喷嘴和文杜利喷嘴 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full – Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003)
EN ISO 5167-4-2003 圆截面管道中用压差装置测量流体流量 第4部分:文杜利管 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full – Part 4: Venturi tubes (ISO 5167-4:2003)
EN ISO 6412-1-1994 技术制图 管道的简化表示法 第1部分:通则和正交表示法 Technical drawings – Simplified representation of pipelines – Part 1: General rules and orthogonal representation (ISO 6412-1:1989)
EN ISO 6412-2-1994 技术制图 管道的简化表示法 第2部分:等角投影 Technical drawings – Simplified representation of pipelines – Part 2: Isometric projection (ISO 6412-2:1989)
EN ISO 6412-3-1996 技术制图 管道的简化表示法 第3部分:通风和排放系统终端部件 Technical drawings – Simplified representation of pipelines – Part 3: Terminal features of ventilation and drainage systems (ISO 6412-3:1993)
EN ISO 6817-1995 封闭管道中导电液体流量的测量 采用电磁流率计的方法 Measurement of conductive liquid flow in closed conduits – Method using electromagnetic flowmeters (ISO 6817:1992)
EN ISO 7235-2003 声学 管道消音器和气端装置的实验室测量步骤 插入损失、流动噪声和总压损失 Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
EN ISO 7278-2-1995 液态烃 动态测量 计量校正系统 第2部分:管道校准 Liquid hydrocarbons – Dynamic measurement – Proving systems for volumetric meters – Part 2: Pipe provers (ISO 7278-2:1988)
EN ISO 8316-1995 封闭管道中液体流量的测定 采用在容积计量容器内收集液体的方法 Measurement of liquid flow in closed conduits – Method by collection of the liquid in a volumetric tank (ISO 8316:1987)
EN ISO 8795-2001 人类生活用水输送用塑料管道系统 迁移评定 塑料管道迁移值的测定 Plastics piping systems for the transport of water intended for human consumption – Migration assessment – Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001)
EN ISO 9080-2003 塑料管与管道系统 用推断法测定热塑管型材料长期流动液体静力强度 Plastics piping and ducting systems – Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003)
ENV 1046-2001 塑料管道和导管系统 运输水或污水用建筑结构外系统 地上和地下安装用规程 Plastics piping and ducting systems – Systems outside building structures for the conveyance of water or sewage – Practices for installation above and below ground
ENV 12097-1997 建筑物通风 管道工程 对便于管道工程系统设施维护的管道工程部件的要求 Ventilation for buildings – Ductwork – Requirements for ductwork components to facilitate maintenance of ductwork systems
ENV 12108-2001 塑料管道系统 在建筑物内安装家用冷热压力管道系统的指南 Plastics piping systems – Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
ENV 1329-2-2001 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVC-U) 第2部分:合格平定指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 2: Guidance for the assessment of conformity
ENV 13801-2000 建筑物中用于粪便和污水排放(低温和高温)的塑料管道系统 热塑性塑料 推荐的安装规范 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Thermoplastics – Recommended practice for installation
ENV 1401-2-2000 非压力地下污废水排放用塑料管道系统硬聚氯乙烯(PVC-U) 第2部分:合格评定 Plastics piping systems for non-pressure underground drainage and sewerage – Unplasticized poly(vinyl chloride) (PVC-U) – Part 2: Guidance for assessment of conformity
ENV 1401-3-2001 非压力地下污废水排放用塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分:安装指南 Plastics piping systems for non-pressure underground drainage and sewerage – Unplasticized poly(vinyl chloride) (PVC-U) – Part 3: Guidance for installation
ENV 1451-2-2001 建筑物结构内污物和污水排出(低和高温)用塑料管道系统 聚丙烯(PP ) 第2部分:合格评定指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polypropylene (PP) – Part 2: Guidance for the assessment of conformity
ENV 1452-6-2001 供水塑料管道系统 硬塑聚氯乙烯(PVC-U) 第6部分:安装指南 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 6: Guidance for installation
ENV 1452-7-2000 供水塑料管道系统 硬聚氯乙烯(PVC-U) 第7部分:合格评定指南 Plastics piping systems for water supply – Unplasticized poly(vinyl chloride) (PVC-U) – Part 7: Guidance for the assessment of conformity
ENV 1453-2-2000 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第2部分:合格评定指南 Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings – Unplasticized poly(vinyl chloride) (PVC-U) – Part 2: Guidance for the assessment of conformity
ENV 1455-2-2001 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 丙烯腈 丁二烯 苯乙烯共聚物 第2部分:合格证评 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Acrylonitrile-butadiene-styrene (ABS) – Part 2: Guidance for the assessment of conformity
ENV 1519-2-2001 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第2部分:合格评定指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) – Part 2: Guidance for the assessment of conformity
ENV 1565-2-2001 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第2部分:合格评定指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Styrene copolymer blends (SAN+PVC) – Part 2: Guidance for the assessment of conformity
ENV 1566-2-2001 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第2部分:合格评定指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Chlorinated poly (vinyl chloride) (PVC-C) – Part 2: Guidance for the assessment of conformity
ENV 1852-2-2000 无压地下排水和污水用塑料管道系统 聚丙烯(PP) 第2部分:合格评定指南 Plastics piping systems for non-pressure underground drainage and sewerage – Polypropylene (PP) – Part 2: Guidance for the assessment of conformity
ENV 1993-4-1-1999 欧洲法典 3:钢结构设计 第4-1部分:竖井、蓄水池和管道 竖井 Eurocode 3: Design of steel structures – Part 4-1: Silos, tanks and pipelines – Silos
ENV 1993-4-2-1999 欧洲法典 3:钢结构设计 第4-2部分:竖井、蓄水池和管道 蓄水池 Eurocode 3: Design of steel structures – Part 4-2: Silos, tanks and pipelines – Tanks
ENV 1993-4-3-1999 欧洲法典 3:钢结构设计 第4-3部分:竖井、蓄水池和管道 管道 Eurocode 3: Design of steel structures – Part 4-3: Silos, tanks and pipelines – Pipelines
ENV 1998-4-1998 欧洲法典8:结构抗震的设计规定 第4部分:竖井 蓄水池和管道 Eurocode 8: Design provisions for earthquake resistance of structures – Part 4: Silos, tanks and pipelines
ENV 737-6-2003 医疗气体管道系统 第6部分:压缩医疗气体和真空用终端部件用探针的尺寸 Medical gas pipeline systems – Part 6: Dimensions and allocation of probes for terminal units for compressed medical gases and vacuum
ENV 852-2001 运输人类用水的塑料管道系统 移动评估 源自移动值的实验室说明指南 Plastics piping systems for the transport of water intended for human consumption – Migration assessment – Guidance on the interpretation of laboratory derived migration values
prEN 1016-1993 塑料管道系统 非可塑聚氯乙烯一端受载的双孔接头 弯曲和内部压力时的密封性和强度试验方法 Plastics piping systems; unplasticized poly(vinyl chloride) (PVC-U) end-load bearing double socket joints; test method for leaktightness and strength while subjected to bending and internal pressure
prEN 10208-3-1997 易燃流体管道用钢管 交货技术条件 第3部分:符合C类要求的管材 Steel pipes for pipelines for combustible fluids – Technical delivery conditions – Part 3: Pipes of requirement class C
prEN 1042-1995 塑料管道系统 聚烯烃管和/或配件间的熔接连接件 恒温下内部压力抵抗力的测定 Plastics piping systems – Fusion joints between polyolefin pipes and/or fittings – Determination of resistance to internal pressure at constant temperature
prEN 1115-2-1997 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第2部分:具挠 Plastics piping systems for underground drainage and sewerage under pressure – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 2: Pipes with flexible, reduced articulation or rigid joints
prEN 1115-4-1993 压力下地下排水和排污装置用塑料管道系统 基于聚脂树脂的玻璃增强热固性塑料(GRP) 第4部分:辅助设备 Plastics piping systems for underground drainage and sewerage under pressure; glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); part 4 (informative): ancillary equipment
prEN 1115-6-1997 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第6部分:安装 Plastics piping systems for underground drainage and sewerage under pressure – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 6: Practices for installation
prEN 1115-7-1995 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料(GRP) 第7部分:一致 Plastics piping systems for underground drainage and sewerage under pressure – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 7: Assessment of conformity
prEN 12666-1-2001 非压力地下排水和排污用塑料管道系统 聚乙烯(PE).第1部分:管道、配件和系统规范 Plastics piping systems for non-pressure underground drainage and sewerage – Polyethylene (PE) – Part 1: Specifications for pipes, fittings and the system
prEN 1329-3-1998 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVCU) 第3部分:安装指南 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 3: Guidance for installation
prEN 1329-5-1994 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVCU) 第5部分:对系统用途的适宜 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system
prEN 1329-6-1994 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 硬塑聚氯乙烯(PVC-U).第6部分:推荐的安装实践 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 6: Recommended practice for installation
prEN 1336-1993 塑料管道系统 热塑性压力管道用终端承载和无承开组件和接头 内部水压力下长期密封性试验方法 Plastics piping systems; end-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping; test method for long-term leaktightness under internal water pressure
prEN 13476-1-2002 非压力地下排水和污水热塑性塑料管道系统 聚氯乙烯(PVC-U)、聚丙烯(PP))和聚已烯(PE)的结构墙管道系 Plastics piping systems for non-pressure underground drainage and sewerage – Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) – Part 1: Specifications for pipes, fittings and the syste
prEN 13480-6-2002 工业用金属管道 第6部分:地下管道的附加要求 Metallic industrial piping – Part 6: Additional requirements for buried piping
prEN 13566-2-2002 用于修复非压力排水和污水网的塑料管道系统 第2部分:带连续管的衬套 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks – Part 2: Lining with continuous pipes
prEN 13636-2003 掩埋金属罐和相关管道的阴极保护 Cathodic protection of buried metallic tanks and related piping
prEN 1401-5-1994 非压力地下污废水排放用塑料管道系统 硬聚氯乙烯(PVC-U) 第5部分:使用系统的适合性 Plastics piping systems for non-pressure underground drainage and sewerage; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system
prEN 14125-2003 汽油加油站的地下管道工程 Pipework for underground installation at petrol stations
prEN 14141-2003 天然气管道输送阀 试验和性能要求 Valves for natural gas transportation in pipelines – Performance requirements and tests
prEN 14161-2003 石油和天然气工业 管道运输系统 Petroleum and natural gas industries – Pipeline transportation systems (ISO 13623:2000 modified)
prEN 14239-2003 建筑物通风 管道系统 管道系统 表面积测量 Ventilation for buildings – Ductwork – Measurement of ductwork surface area
prEN 14280-2001 地下电缆管道的塑料管线系统 未增塑聚氯乙烯 塑料管、管件及管线规范 Plastics piping systems for buried cable ducting – Unplasticized poly(vinyl chloride) (PVC-U) – Specifications for pipes, fittings and the system
prEN 14281-2001 地下电缆管道的塑料管线系统 聚乙烯 塑料管、管件及管线规范 Plastics piping systems for buried cable ducting – Polyethylene (PE) – Specifications for pipes, fittings and the system
prEN 14282-2001 地下电缆管道的塑料管线系统 聚丙烯 塑料管、管件及管线规范 Plastics piping systems for buried cable ducting – Polypropylene (PP) – Specifications for pipes, fittings and the system
prEN 14283-2001 一般用途地下管道的塑料管线系统 未增塑聚氯乙烯 塑料管、管件及管线规范 Plastics piping systems for general purpose buried ducting – Unplasticized poly(vinyl chloride) (PVC-U) – Specifications for pipes, fittings and the system
prEN 14284-2001 一般用途地下管道的塑料管线系统 聚乙烯 塑料管、管件及管线规范 Plastics piping systems for general purpose buried ducting – Polyethylene (PE) – Specifications for pipes, fittings and the system
prEN 14285-2001 一般用途地下管道的塑料管线系统 聚丙烯 塑料管、管件及管线规范 Plastics piping systems for general purpose buried ducting – Polypropylene (PP) – Specifications for pipes, fittings and the system
prEN 1445-2000 纤维水泥管道 现场压力试验 Fibre-cement pipelines – Field pressure testing
prEN 1451-3-1994 建筑物结构内用于污物和污水排放(高/低温)的塑料管道系统 聚丙烯(PP) 第3部分:管件 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polypropylene (PP) – Part 3: Fittings
prEN 1451-5-1994 建筑物结构内用污物和污水排放(高/低温)的塑料管道系统 聚丙烯(PP) 第5部分:系统用途的适合性 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polypropylene (PP) – Part 5: Fitness for purpose of the system
prEN 1451-6-1994 建筑物结构内用于污物和污水排放(高/低温)的塑料管道系统 聚丙烯(PP) 第6部分:推荐的安装实践 Plastics piping systems for soil and waste discharge (low and high temperature) within the building – Polypropylene (PP) – Part 6: Recommended practice for installation
prEN 1453-3-1998 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第3部分:安装指南 Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 3: Guidance for installation
prEN 1453-5-1994 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第5部分:系统用管件 Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fittings for purpose of the system
prEN 1453-6-1994 建筑物内污物和废水排放(低和高温)带结构壁管道的塑料管道系统 硬聚氯乙烯(PVC-U) 第6部分:推荐安装实践 Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 6: recommended practice for installation
prEN 1455-3-1994 建筑物结构内用于污物和污水排放(高/低温)的塑料管道系统 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第3部分 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Acrylonitrile-butadiene-styrene (ABS) – Part 3: Fittings
prEN 1455-6-1994 建筑物结构内用于污物和污水排放(高/低温)的塑料管道系统 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第6部分 Plastics piping systems for soil and waste discharge (low and high temperature) within the building – Acrylonitrile-butadiene-styrene (ABS) – Part 6: Recommended practice for installation
prEN 1456-3-1994 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) .第3部分:管件 Plastics piping systems for underground drainage and sewerage under pressure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 3: Fittings
prEN 1456-4-1994 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第4部分:阀门及辅助设备 Plastics piping systems for underground drainage and sewerage under pressure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 4: Valves and ancillary equipment
prEN 1456-5-1994 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第5部分:对系统用途的适宜性 Plastics piping systems for underground drainage and sewerage under pressure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 5: Fitness for purpose of the system
prEN 1456-6-1994 地上和地下污废水压力排放用塑料管道系统 硬已烯(聚氯已烯)(PVC-U) 第6部分:推荐的安装实践 Plastics piping systems for underground drainage and sewerage under pressure – Unplasticized poly(vinyl chloride) (PVC-U) – Part 6: Recommended practice for installation
prEN 1507-2002 建筑物通风 管道系统 矩形金属片通风管道 强度和泄露 要求和试验 Ventilation for buildings – Sheet metal air ducts with rectangular section – Requirements for strength and leakage
prEN 1519-3-1994 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第3部分:管件 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) – Part 3: Fittings
prEN 1519-5-1994 建筑物结构内污物和污水排放(低和高温)塑料管道系统.聚已烯(PE) 第5部分:针对系统用途的适合性 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) – Part 5: Fitness for purpose of the system
prEN 1519-6-1995 建筑物结构内污物和污水排放(低和高温)塑料管道系统 聚已烯(PE) 第6部分:推荐的安装实践 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Polyethylene (PE) – Part 6: Recommanded practice for installation
prEN 1555-6-1995 供给气体燃料用塑料管道系统 聚已烯(PE) 第6部分:推荐的安装实践 Plastics piping systems for gaseous fuels supply – Polyethylene (PE) – Part 6: Recommended practice for installation
prEN 1565-3-1994 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第3部分:管件 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Styrene copolymer blends (SAN+PVC) – Part 3: Fittings
prEN 1565-5-1994 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第5部分:针对系统用途 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Styrene copolymer blends (SAN+PVC) – Part 5: Fitness for purpose of the system
prEN 1565-6-1995 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 苯乙烯共聚混合物(SAN+PVC) 第6部分:推荐的安装实 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Styrene copolymer blends (SAN + PVC) – Part 6: Recommended practice for installation
prEN 1566-3-1994 建筑物结构内污物和废水排放(低和高温)用塑料管道系统 氯化聚偏氯乙烯(PVC-C) 第3部分:管件 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Chlorinated poly(vinyl chloride) (PVC-C) – Part 3: Fittings
prEN 1566-5-1994 建筑物结构内污物和污水排放(低和高温)用塑料管道系统 氯化已烯(聚氯已烯)(PVC-C) 第5部分:针对系统用途 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure – Chlorinated poly(vinyl chloride) (PVC-C) – Part 5: Fitness for purpose of the system
prEN 1636-1-1996 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第1部分:总则 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 1: General
prEN 1636-2-1996 无压力排水道和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第2部分:带有挠 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) – Part 2: Pipes with flexible, reduced articulation or rigid joints
prEN 1636-4-1994 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP) 第4部分:辅助设备 Plastics piping systems for non-pressure drainage and sewerage – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 4: Ancillary equipment
prEN 1763-2-2000 供气相丙烷和丁烷使用的挠性软管、管道及组装件 第2部分:对管咀接头及组装件的要求 Flexible hose, tubing and assemblies for use with propane and butane in the vapour phase – Part 2: Requirements for nozzles, couplings and assemblies
prEN 1796-2-1995 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 第2部分:带挠性、缩口活节或刚性 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 2: Pipes with flexible, reduced articulation or rigid joints
prEN 1796-2003 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
prEN 1796-3-1995 有或无压力供水用塑料管道系统聚合物树脂(UP)基玻璃纤维增强热固性塑料(GRP) 第3部分:管件 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 3: Fittings
prEN 1796-4-1995 有或无压力供水有塑料管道系统聚合物树脂(UP)基玻璃纤维增强热固性塑料(GRP) 第4部分:辅助设备 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 4: Ancillary equipment
prEN 1796-5-1995 有或无压力供水用塑料管道系统聚合物树脂(UP)基玻璃纤维增强热固性塑料(GRP) 第5部分:系统用途的适合 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 5: Fitness for the purpose of the system
prEN 1796-6-1995 有或无压力供水用塑料管道系统聚合物树脂(UP)基玻璃纤维增强热固性塑料(GRP) 第6部分:推荐的安装实践 Plastics piping systems for water supply with or without pressure – Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) – Part 6: Recommended practice for installation
prEN 1852-5-1995 无压地下排水和污水用塑料管道系统 聚炳烯(PP) 第5部分:对系统配合的适宜性 Plastics piping systems for non-pressure underground drainage and sewerage – Polypropylene (PP) – Part 5: Fitness for purpose of the system
prEN 45512-1994 采购指南 管道系统和阀 包括安全阀的锅炉和高压管道阀 Guide for procurement – Pipework and valves – Boiler and high pressure piping valves including safety valves
prEN 45513-1994 采购指南 管道系统和阀 包括支架的高压管线 Guide for procurement – Pipework and valves – High pressure piping including supports
prEN 474-9-2001 土方机械 安全 第9部分:管道敷设机的要求 Earth-moving machinery – Safety – Part 9: Requirements for pipelayers
prEN 50085-2-1-2002 电气装置用电缆槽和电缆管道系统 第2-1部分:安装在墙上或天花板上的电缆槽和电缆管道系统的特殊要求 Cable trunking and cable ducting systems for electrical installations – Part 2-1: Particular requirements for cable trunking systems and cable ducting systems intended for mounting on walls and/or ceilings
prEN 762-1995 塑料管道和导管系统 热塑系统用弹性密封接头 密封环保持力和损坏的试验方法 Plastics piping and ducting systems – Joints with elastomeric seals for thermoplastic systems – Test method for retention of, and damage to, sealing rings
prEN 806-3-2003 建筑物内人类用水输送装置规范 第3部分:管道尺寸 Specifications for installations inside buildings conveying water for human consumption – Part 3: Pipe sizing
prEN 987-1995 塑料管道和导管系统 铸模装置 装置中磨掉碎片摆锤式冲击试验强度的测定 Plastics piping and ducting systems – Injection-moulded fittings – Determination of the Charpy impact strength of test pieces cut from a fitting
prEN ISO 10806-2003 管道工程 皱纹软金属管用非合金及不锈钢配件 Pipework – Fittings for corrugated metallic hoses (ISO/FDIS 10806:2003)
prEN ISO 14828-1999 塑料管道系统 玻璃纤维增强热固塑料管 在湿环境下长期特殊环形松弛劲度的测定和湿松弛系数的计算 Plastics piping systems – Glass-reinforced thermosetting plastics (GRP) pipes – Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor (ISO/DIS 14828:1999)
prEN ISO 15002-1996 医用气体管道系统终端装置用气流量测量装置 Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO/DIS 15002:1996)
prEN ISO 15465-2002 管道工程 条绕金属软管和软管组件 Pipework – Stripwound metal hoses and hose assemblies (ISO/DIS 15465:2002)
prEN ISO 15749-2-2001 船舶和造船技术 船和海上构筑物上排水系统 第2部分:生活污水排水、排水管道的自流系统 Ships and marine technology – Drainage systems on ships and marine structures – Part 2: Sanitary drainage, drain piping for gravity system (ISO/DIS 15749-2:2001)
prEN ISO 15749-4-2001 船舶和造船技术 船和海上构筑物上排水系统 第4部分:生活污水排水、污物处理排出管道 Ships and marine technology – Drainage systems on ships and marine structures – Part 4: Sanitary drainage, sewage disposal pipes (ISO/DIS 15749-4:2001)
prEN ISO 15874-1-2002 冷热水用塑料管道系统 聚乙烯(PE) 第1部分:总则 Plastics piping systems for hot and cold water installations – Polypropylene (PP) – Part 1: General (ISO/FDIS 15874-1:2002)
prEN ISO 15874-2-2002 冷热水用塑料管道系统 聚丙烯(PP) 第2部分:管道 Plastics piping systems for hot and cold water installations – Polypropylene (PP) – Part 2: Pipes (ISO/FDIS 15874-2:2002)
prEN ISO 15874-3-2002 冷热水用塑料管道系统 聚丙烯(PP) 第3部分:配件 Plastics piping systems for hot and cold water installations – Polypropylene (PP) – Part 3: Fittings (ISO/FDIS 15874-3:2002)
prEN ISO 15874-5-2002 冷热水用塑料管道系统 聚丙烯(PP) 第5部分:系统目的的适配性 Plastics piping systems for hot and cold water installations – Polypropylene (PP) – Part 5: Fitness for purpose of the system (ISO/FDIS 15874-5:2002)
prEN ISO 15875-1-2002 冷热水塑料管道系统 交联聚乙稀( PE – X ) 第1部分:总则 Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 1: General (ISO/FDIS 15875-1:2002)
prEN ISO 15875-2-2002 冷热水塑料管道系统 交联聚乙稀( PE – X ) 第2部分:管道 Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 2: Pipes (ISO/FDIS 15875-2:2002)
prEN ISO 15875-3-2002 冷热水塑料管道系统 交联聚乙稀( PE – X ) 第3部分:接头 Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 3: Fittings (ISO/FDIS 15875-3:2002)
prEN ISO 15875-5-2002 冷热水塑料管道系统 交联聚乙稀( PE – X ) 第5部分:系统适用性 Plastics piping systems for hot and cold water installations – Crosslinked polyethylene (PE-X) – Part 5: Fitness for purpose of the system (ISO/FDIS 15875-5:2002)
prEN ISO 15876-1-2002 冷热水塑料管道系统 聚丁稀( PB ) 第1部分:总则 Plastics piping systems for hot and cold water installations – Polybutylene (PB) – Part 1: General (ISO/FDIS 15876-1:2002)
prEN ISO 15876-2-2002 冷热水塑料管道系统 聚丁稀( PB ) 第2部分:管道 Plastics piping systems for hot and cold water installations – Polybutylen (PB) – Part 2: Pipes (ISO/FDIS 15876-2:2002)
prEN ISO 15876-3-2002 冷热水塑料管道系统 聚丁稀( PB ) 第3部分:接头 Plastics piping systems for hot and cold water installations – Polybutylen (PB) – Part 3: Fittings (ISO/FDIS 15876-3:2002)
prEN ISO 15876-5-2002 冷热水塑料管道系统 聚丁稀( PB ) 第5部分:系统适用性 Plastics piping systems for hot and cold water installations – Polybutylen (PB) – Part 5: Fittness for purpose of the system (ISO/FDIS 15876-5:2002)
prEN ISO 15877-1-2002 冷热水用塑料管道系统 氯化聚氯乙烯(PVC-C)第1部分:总则 Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 1: General (ISO/FDIS 15877-1:2002)
prEN ISO 15877-2-2002 冷热水用塑料管道系统 氯化聚氯乙烯(PVC-C)第2部分:管道 Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 2: Pipes (ISO/FDIS 15877-2:2002)
prEN ISO 15877-3-2002 冷热水用塑料管道系统 氯化聚氯乙烯(PVC-C)第3部分:接头 Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 3: Fittings (ISO/FDIS 15877-3:2002)
prEN ISO 15877-5-2002 冷热水用塑料管道系统 氯化聚氯乙烯(PVC-C)第5部分:系统用途的适合性 Plastics piping systems for hot and cold water installations – Chlorinated poly(vinyl chloride) (PVC-C) – Part 5: Fitness for purpose of the system (ISO/FDIS 15877-5:2002)
prEN ISO 580-2002 塑料管与管道系统 注模制热塑性塑料配件 加热反应的视觉评估方法 Plastics piping and ducting systems – Injection-moulded thermoplastics fittings – Methods for visually assessing the effects of heating (ISO/DIS 580:2002)
prEN ISO 7369-2002 管道工程 金属软管和软管装备 词汇 Pipework – Metal hoses and hose assemblies – Vocabulary (ISO/DIS 7369:2002)

Related News

  • * 暂无相关文章
العربيةБългарски简体中文繁體中文DanskNederlandsEnglishFrançaisDeutschBahasa IndonesiaItaliano日本語한국어LatinPortuguêsРусскийEspañolதமிழ்ไทยTürkçe