Recently Shipment to Mid Asia Projects

Pipeline valve installation

1 Valve installation position must be convenient for operation Even if the installation is temporarily difficult, it is necessary to think about the long-term work of the operator. It is best to have the valve handwheel and the chest (usually 1.2 meters away from the operating floor), so that the opening and closing of the valve is more labor-saving. The floor valve hand wheel should be facing up, do not tilt, so as to avoid awkward operation. The valve against the wall machine should also leave room for the operator to stand. It is necessary to avoid the operation of […]

Recently Shipment to Mid Asia Projects

What is a threadolet?

What is a threadolet? A threadolet is the same basic design as a “weldolet.” However the main difference is the fitting has a female threaded connection to mate to the branch connection. This makes a 90° branch and comes in full size or reducing for a straight piece of pipe. It typically is in the size range of 1/2″ to 2″ and is welded over a hole either drilled or burned in the pipe.  You use a “weldolet” when you want to weld a steel pipe or pipe fitting directly to the branch fitting and a “threadolet” when you want to […]

Recently Shipment to Mid Asia Projects

What is a weldolet?

What is a weldolet? A Weldolet has beveled ends at both ends and is, therefore, welded onto the run pipe on one side and onto the branch pipe on the other side. Weldolets are used to create a 90-degrees (reinforced) pipe branch. The shape of the weldolet ensures little stress concentration on the branched pipe, providing an integral reinforcement. On the branch pipe side, Weldolets may have the same schedule of the run pipe or a higher schedule. It Comes in full size or reducing size (Full size is when you take branch of the same size as run pipe […]

Recently Shipment to Mid Asia Projects

What is a sockolet?

What is a sockolet? The sockolet (socket weld outlet) is mainly used for the reinforcing pipe fittings connected by the branch pipe, instead of using the branch pipe type such as the reducer, the reinforcing plate and the reinforcing pipe section, it is safe and reliable, reduces the cost, simple construction, improves the medium flow channel, and series. The advantages of standardization, design and selection are convenient, especially in high-pressure, high-temperature, large-diameter, thick-walled pipelines, which replaces the traditional branch pipe connection method. The main body of the branch pipe is made of high-quality forgings, and the materials are the same […]

Recently Shipment to Mid Asia Projects

Analysis of the installation case of spiral wound gaskets

Large diameter spiral wound gaskets are key sealing elements for heat exchanger channel flanges. In order to minimize seal failure at the heat exchanger channel flange, it is important to properly install the spiral wound gasket and apply the correct bolt tightening sequence and proper tightening torque. 1 Question raised An industrial refrigeration project exported to Kazakhstan, the U-tube heat exchanger, according to GB 151 for the heat exchanger, its model is BIU1500-8.3/2.07-1142-7/19-2 (As shown in Figure 1), the design pressure is 8.3 MPa, the hydraulic pressure test pressure is 10.8 MPa; the full thread bolt is M64×3, the length […]

Recently Shipment to Mid Asia Projects

What is a steel tee

What is a steel tee? The steel tee is a pipe fitting and a pipe joint. Used to change the direction of the fluid, used in the branch pipe of the main pipe. The three-way is a chemical pipe fitting with three openings, namely one inlet and two outlets; or two inlets and one outlet, having T-shaped and Y-shaped shapes, with equal-diameter nozzles and different diameter nozzles. Three identical or different pipeline collections. Classification of pipe tees What is an equal tee What is a reducing tee What is a lateral tee What is a barred tee What is a […]

Recently Shipment to Mid Asia Projects

ASME B16.34 – Group, Pres-Temp Rating

ASME B16.34 Valves Flanged, Threaded and Welding End applies to new construction. It covers pressure-temperature ratings, dimensions, tolerances, materials, nondestructive examination requirements, testing, and marking for cast, forged, and fabricated flanged, threaded, and welding end and wafer or flangeless valves of steel, nickel-base alloys, and other alloys shown in Table 1. Wafer or flangeless valves, bolted or through-bolt types, that are installed between flanges or against a flange are treated as flanged-end valves. Alternative rules for NPS 2½ and smaller valves are given in Mandatory Appendix V.  This Standard is to be used in conjunction with equipment described in other […]

Recently Shipment to Mid Asia Projects

Flange production and processing technology

Flanges have a variety of connection methods. According to different industry standards, they can be divided into a variety of flanges. The materials, processing forms and processes are different. The production and processing of flanges are mainly divided into forging, casting and cutting. These four systems are made and rolled. Material Alloy Steel: ASTM A182 F1, F5a, F9, F11, F12, F22, F91, A182F12, A182F11, 16MnR, Cr5Mo, 12Cr1MoV, 15CrMo, 12Cr2Mo1, A335P22, Carbon Steel: ASTM A105, 20#, Q235, 16Mn, ASTM A350 LF1, LF2 CL1/CL2, LF3 CL1/CL2, ASTM A694 F42, F46, F48, F50, F52, F56, F60, F65, F70 ; Common pressure levels: PN6, […]

Recently Shipment to Mid Asia Projects

BUILDEXPO AFRICA 2019 – Region’s Prime International Trade Exhibit……

BUILDEXPO AFRICA 2019 – Region’s Prime International Trade Exhibitions On Building & Construction. Ethiopia: 21 – 23 March ’19, Addis Ababa | Rwanda: 23 – 25 May ’19, Kigali | Kenya : 04 – 06 July ’19, Nairobi | Tanzania : 12 – 14 Sept. ’19, Dar-es-Salaam About BuildExpo: Buildexpo Africa is the only show with the widest range of the latest technology in building material, mining machines, construction machinery and heavy equipment. At the 22nd edition of Buildexpo, East Africa’s largest building and construction fair, we bring you exhibitors from over 40 countries who are the finest in infrastructure […]

Recently Shipment to Mid Asia Projects

What is a plunger valve?

What is a plunger valve? Plunger valve is composed of valve body, valve cover, valve stem, plunger, hole rack, sealing ring, handwheel and other parts. When the handwheel rotates, the valve opens and closes by driving the plunger up and down in the middle of the hole rack by the valve stem. The interference fit between the plunger and the sealing ring is adopted in the valve. By adjusting the flange bolt in the pressure cap, the lateral force produced by the compression of the sealing ring is sealed with the orifice in the valve body and the outer circle […]

العربيةБългарски简体中文繁體中文DanskNederlandsEnglishFrançaisDeutschBahasa IndonesiaItaliano日本語한국어LatinPortuguêsРусскийEspañolதமிழ்ไทยTürkçe